The Old Bake House Office

31 Moorgreen

Nottingham

NG162FD

United Kingdom

Payment
PAYMENT IS ACCEPTED VIA PAYPAL, DEBIT/CREDIT CARD
OR CALL US AND PAY VIA TELEPHONE 

 from 9 to 5    

gibidi@gibidimotors.co.uk

We Post To Mainland UK and Ireland
postage is  at checkout.... 

Yes we are shipping to the Republic of Ireland  

CALL US FOR TRADE PRICES

Outside of the UK or IRELAND you can always arrange

your own shipping

We will package up your goods ready for your courier to pickup from our address

If You Have Problems Call

Sales 01773 719 347
Or Call Adrian 07971475781.      sales@gibidimotors.co.uk

Upgrade this from the standard delivery to a pre 10.30 or AM delivery if you require the product more urgently. Timed Saturday or Sunday deliveries and  delivery option are also available if required at extra cost call for more information

All control panels and motors tested before dispatch. 

Thank you for choosing GI.BI.DI.

NEW VD909/L Diablo In-Road Vehicle Sensor Pulse Only

£136.67

Only 3 remaining

NEW VD909/L Diablo Magna In-Road Vehicle Sensor Pulse Only

VD909/L is an exit sensor with 3 separate sensitivity plugins

Diablo VD909/L sensor is designed for easy vehicle entry & exits. Easy fitting allows for quick installations whilst resistive wiring requires very little maintenance.

VD909 has 3 sensitivity outputs
10V - 30V AC/DC
NO COM NC
PULSE ONLY
Sensitivity Inductor Pack INCLUDED
Exit Sensor with 18m Fly Lead & Module

Description

Diablo VD909 Mini Exit Sensor & Module Kit

Exit Sensor & 18m Lead

The ‘Dynamite’ mini loop is a unique vehicle detector device in a 22mm diameter tube.

An integral ground cable runs back to a module in your control panel. Dynamite gives a pulse output when a vehicle drives over. It is not a safety device

Diablo VD909 Mini Exit Sensor & Module Kit Simple installation

Drill a 25mm hole in the middle of the driveway for the yellow sensor, then cut a shallow slot for the cable from the hole directly to the control panel (no need for loops to be cut). Connect to the small module in the control panel which has auto-setting. Fill slot with road repair material. It really is that Simple!

Basic Installation Guide
Installation is straightforward. A 1-in. diameter hole (18-in to 24-in. deep) is drilled for the “Mini Loop”. A shallow, 1/4-in. saw cut from the hole to the edge of the road provides a path for the lead-in wire. The “Mini-Loop” with lead-in is inserted into the hole and the hole is filled with dry sand. Detector Loop Sealant material is then used to fill the slot and top portion of the hole. It is important that the “Mini-Loop” be installed in a vertical position and that the vertical position of the “Mini-Loop” be maintained. Under some soil conditions, installation can be further simplified by installing the Mini-Loop inside a length of PVC pipe (not steel pipe) with an interior diameter of about 1 inch. In this case, the hole must be slightly larger than the outside diameter of the PVC pipe, typically 1-5/8-in. or less. After insertion of the PVC pipe and Mini-Loop, all cavities are back-filled with fine, dry sand and the installation completed in the normal manner.

Detection Area
With most vehicles, detection will start at approximately the front bumper and end at approximately the rear bumper. Oddly shaped vehicles such as bicycles and trailers may appear shorter to the Mini-Loop than their actual length. For example, some bicycles detect only for a short period of time near the middle of the bicycle. Aluminium or fibreglass trailers will likely detect only for a short period of time around the axle and suspension. These characteristics are very similar to those of a 6-ft. X 6-ft. loop. The primary difference is that the Mini-Loop in itself is only a point rather than a 36 square foot area. This allow

CALL ADRIAN FOR MORE INFO 07971475781

Want to know more or have any questions? Use the contact form below to discuss your requirements

2020 Copyright A T Ball Electrics All Rights Reserved

gibidi@gibidimotors.co.uk

  Office 01773 719347    

        Sales Call for card payments     

     Adrian 07971 475781

 

Head office:-The Old Bake House Office 31 Moorgreen Newthorpe Nottingham NG162FD

VAT Registration Number is 230 5806 33

PLEASE NOTE : ITEMS WILL NOT BE LEFT BY COURIER WITHOUT BEING SIGNED FOR.

Most small items are sent by post and we are unable to instruct the postman to leave Items.



Screenshot 2021-08-23 at 163418png


Don't know the parts you need text, email or whatsapp a picture to Adrian on 07971475781 or email gibidi@gibidimotors.co.uk with a picture of the broken part or a picture from the back of your gates with a description of the problem and we will do what we can to help

https://wa.me/message/LP5UHOVQRKGNF1