£45.49 Inc VAT
GIBIDI AU02910 GIBIDI 1 X PLUG IN 2 WAY RECEIVER UNIT 433 Mhz rolling code
For GIBIDI 1 X PLUG IN 2 WAY RECEIVER UNIT
Including memory chip
To program press button on receiver then when red light is on press
remote button 1 on remote ....That's it programmed !Will fit plus 2
control panels F3+, F4+, BA24, BA230, SC24, SC230 and many more .
Plug-in receiver ( 433Mhz )
433 Mhz rolling code
Managed Plug in Receiver With 2 Channels
Follow link for programming gibidi 433 video https://vimeo.com/178172262
Remote Transmitter Fob
Configuring Additional Remote Transmitter Fobs
Additional transmitter fobs can be configured to work with
the existing installation.
In order to do this you need to be standing in front of the control box
by the gates.
USING AN EXISTING WORKING GENUINE GIBIDI DOMINO TRANSMITTER FOB...Press
buttons 1 and 2 together at the same time for 8 continuous seconds.
Then within five seconds...
Briefly press the button 1 on the new remote transmitter fob.
Leave the system for 10 seconds.
Press the button on the newly configured
transmitter fob and the gates should open.
Do not press the
Radio Transmitter Fob Button without seeing that the gate is
clear of obstructions.
To program a genuine Domino remote
USING AN EXISTING WORKING GENUINE GIBIDI DOMINO TRANSMITTER FOB...You
can do this by going to the control panel of
gates Take the lid off the motor so you can see control panel and see through
cover Then undo the screw by you at the end of the control panel by wiring then
loosen the 2 screws at the far end away from the wiring to lever the see
through lid up away from the wiring then at the far end away from the wiring
there is a pcb card sticking up with a RED L.E.D and BUTTON by it ….
(2) Swing gates
go to the control panel remove the lid and on right hand side ½ way up there is
a PCB card sticking out with a RED L.E.D and BUTTON by it
button briefly until red L.E.D comes on then press ONLY BUTTON 1 on remote….
THAT’S IT PROGRAMMED! THEN REPEAT FOR MORE REMOTES…
If red L.E.D goes out press button again and repeat with other
THIS PROGRAMS ALL 4 BUTTONS …. ONLY EVER PRESS BRIEFLY BUTTON 1 ON
REMOTE FOR PROGRAMMING!
Don’t worry if you use buttons 2,3 or 4 as by pressing briefly button 1 this programmes all 4 buttons
If you have
2 button Gibidi remote follow the instructions but you can press the button you
want to work the gates!
Don’t Press the receiver card button in for more than 5 seconds as this
could delete all programmed remotes already programmed into it!
Clearing the receiver card memory
if a handset has been lost or stolen)
the programming button on the receiver/control PCB. Press this button briefly
then press a second time
hold it down until the L.E.D goes out then follow steps (A) or (b) above to
re-program key fobs again
Also by trying to program copy remotes this could stop genuine remotes
Delete all other programmed
remotes from the receiver unit
Regular Maintenance by User
The Radio Transmitter Fob is battery powered. As the battery life
diminishes, the range of transmission will decrease. When the red L.E.D. does
not light up, you
should change your battery….
If you have problems you can give us a call at Gibidi automation on
We Sock Spare Gibidi Parts &
Full Gate Automation Kits Above Ground & Under Ground Motors For Swing Twin
Leaf & Single Leaf Gates As Well As Sliding Gate Motors & Barrier /
Bollard Motors of various sizes
The Control Manuals For Gibidi https://www.gibidimotors.co.uk/gibidi-electric-gate-automation-control-wiring